HOW TO FLASH [ONLY MEDIATEK] HARD BRICKED(STAGE 1) ANDROID (TOTALLY DEAD) DEVICE

Author: DT HACK & JOB
135570 View
3m 0s Lenght
Rating

╔═╦╗╔╦╗╔═╦═╦╦╦╦╗╔═╗ ║╚╣║║║╚╣╚╣╔╣╔╣║╚╣═╣ ╠╗║╚╝║║╠╗║╚╣║║║║║═╣ ╚═╩══╩═╩═╩═╩╝╚╩═╩═╝ ✪Fix all Types of SP Flash Tool Error ➤https://www.youtube.com/watch?v=MX8OxGgM5Bw ►►HINDI VERSION:-https://www.youtube.com/watch?v=eWT-tLRm73A Guys if want to discuss more than come to our facebook page:- ►http://www.facebook.com/dthackandjob◄ ◄►Link for SP Flash Tool(for MEDIATEK users):-http://spflashtool.com/◄► Hard Brick:- When the device has gone through problematic conditions such that it quits the detection of USB, charging and everything that you provide to it then the device is unfortunately hard bricked. Some hard bricked devices are as good as a paper weight that we paid for some day. But that is the extreme case lets see what are the two stages we can observe here: Stage one: At stage one the device keeps getting disconnected every 5-8 seconds when you connect it with the flash tool via data cable (specially with the mtk devices I have seen). So in that cases we only have few seconds of time gap so that we can make the flash tool to detect the device. Hence, we have to find out certain key combos on the device which will lead to detection of your bricked device to flash the "stock ROM" while it kept connected to the data cable. Key combos could be: * Volume Up + Power button * Volume Down + Power button * Volume Up + Volume Down * Power button alone Stage two: It occurs when some serious hardware damage happened to the device such as malfunctioning of the motherboard, Processors, Internal circuits etc. If the device reaches to this condition then it does needs repair on the segment of the hardware. In case if the device is under warranty then I recommend not to break the seal of the company or else the warranty will get void. I think you got a little idea about the bricking of the devices and how to figure out if the device is hard or soft bricked. Good luck and a happy yet cautious flashing to you all. ERROR 4032 SOLUTION:-just follow this method 100% works fr all.... 1.download the SP Flash Tool V5.1352.01 2.select the scatter file from your original rom 3.go to "options" in the flash tool-options-connections-battery-select W/O battery 4.now go back and click on download and after that connect ur phone WITHOUT BATTERY to pc via usb cable and then just wait for few min. till the flashing over...... and after flashing disconnect phone from pc and then just start the phone and just ur done hope it helps any queries reply here like and subscribe :) ☎☎☎☎☎☎☎۩ CONNECT WITH ME ۩☎☎☎☎☎☎☎☎☎ ☠Subscribe➤ https://www.youtube.com/c/DurgeshThakurdthacksandjobs?sub_confirmation=1 ✪Join Group➤ https://www.facebook.com/groups/549117165295942 ☯Join Community➤ https://plus.google.com/u/0/communities/104307297318953975855 ✔Facebook➤ https://www.facebook.com/dthackandjob ✔Twitter➤ https://www.twitter.com/dthackandjob ✔Instagram➤ https://www.instagram.com/dthackandjob ✔Blog➤ http://dthackandjob.blogspot.in/ ✔G-Plus➤ http://bit.ly/29h5q79 ✔Linkedin➤ https://in.linkedin.com/in/durgesh-thakur-a07222115 ══════۩ IGNORE THE TAGS ۩═════ How to flash dead device how to flash hard bricked android device android device is dead what to do hard bricked after flashing wrong rom hard bricked only charging notification hard bricked android no boot my phone is dead phone not goes to recovery my phone not detected by sp flash tool Phone power up too early device power up too early BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005) [BROM] Can not pass bootrom start command! Possibly target power up too early. [BROM] Can not pass bootrom start command! Possibly target power up too early. S_BROM_CMD_STARTCMD_FAIL (2005)

Comments

  1. my phone not on totally dead and my problem not solve
  2. hii frnd i have p3100 my phone problem is that its restarting in every 1
    min i have tried factory reset , wipe all data , almost everythings
    again all data my photo n videos are back like ghost PLZ ANY ONE HELP
    WHAT TO DO
  3. thank you worked for me
  4. i have moto e it is fully dead how will i get scatter file from rom folder i just serch whole folder there was no scatter file pleaze give the link where i have to download scatter file
  5. it this working for tablets?
  6. its not ok, i got an error like S_FT_ENABLE_DRAM_FAIL
  7. khatarnak Nuska :P but kaam kar gya :D
  8. when I power on my android it does not power on only whit screen appears is it dead or not
  9. my meizu m2 is not flashing any ROM via SP flash tool and installing recovery with CMD it shows Failed not allowed
  10. sir my Karbon Android one sparkle v doesn't format by sp tool.. it shows sometime broom error or sometimes pmt error I can't able to flash my mobile due to this pls assist me
  11. Where to download htc 816 dual sim scatter file[mt6582]
  12. 100 % flash hone ke bad bhi on nahi hora
    kya ye ROM me bug ki wajah se hai?
  13. 1 NIUMBER YAAR TU CHAVAA HAI YAR
  14. my phone is not connected to PC
  15. my yureka plus showing while on download IMG failed what should i do
  16. Thanks I got my phone back 😊😉
  17. My phone panasonic eluga i2 dead after flashing and its shows not charging and even not start and it also doesnt sound while connect the pc i also download the drivers but nothing happen what should i do???

    pls help...
  18. what is the "original rom" for step 3?
  19. i'm gettin the error message: :STATUS_DA_EXCEED_MAX_NUM(0xC00700005) you know help me?
  20. Hi actually my device was hard bricked but I flashed it and it is okay but I m not able to boot in recovery mode is say SMT CFT fail is there any solution